cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Advocate

Hub Two and Network switches

I'm looking for help please.

 

I've recently tried to connect a network switch to my hub two.

 

Unfortunately I'm not getting any internet through the switch.

 

If I connect the same device directly to the router then it works, which lead me to believe it was either the cables or the switch.

 

I've tried different cables, and tried the switch at a friend's house where it worked perfectly (with another broadband provider).  I bought another switch by a different manufacturer but still have the same issue.

 

It's been suggested to me that I could have this issue of ports are blocked on the router, I've been into settings but cannot see this information.

 

Is this likely to be a cause or could there be compatibility issues?  Any help would be much appreciated.

0 Thanks
Reply
6 Replies
Highlighted
Legend 5
Legend 5

Re: Hub Two and Network switches

@Sunrise Shot in the dark here, but have all the cables you’ve tried been fully wired? A lot of cheap ethernet cables only have 4 wires (the minimum, older standard). It’s possible that the ethernet switch needs all 8 wires in the cable between it and the router, especially if you’re using the gigabit port on the router if it has one. 

Blocked, or open ports on the router have nothing to do with this issue as this is a purely hardware problem.

 

 

0 Thanks
Reply
Highlighted
Advocate

Re: Hub Two and Network switches

@Mark_Weinreb 

 

The cables are cat6 gigabit ethernet cables.

 

 

0 Thanks
Reply
Highlighted
Legend 5
Legend 5

Re: Hub Two and Network switches

@Sunrise I did say it was a shot in the dark.

 

So, more questions:

1. When you connected to device directly to the router, did you use the same cable you use to connect the switch to the router?

2. When you tried the switch at you friend’s  house, whose cable did you use? If you used his, any chance you could borrow it to try in your set-up? If you used your friend’s cable at his house, try again using your cable.

3. Are you certain, and I’m sure you are, that the cat-6 cable is a standard patch cable? There are some differently wired cables out there.


The process of elimination is long, boring and often leads dented walls - the result of bashing one’s head against them.

 

One other thing, are you using the gigabit port on your router (if there is one)?

0 Thanks
Reply
Highlighted
Legend 5
Legend 5

Re: Hub Two and Network switches

@Sunrise 

 

@Mark_Weinreb touched on ‘differently wired cables’ of which the usual type is a crossover cable. 

Make sure you haven’t got any of these in the mix - it’s usually specified on a label or on the sheathing - and that all yours are straight-throughs.


If my posting answered your question, please click ‘Accept Answer’
(As long as you started the thread, and haven’t already accepted an answer)
If you liked my posting, please click ‘Thanks’ (the thumbs-up icon)
If you disagree with my posting, say so below, and I will see if I need to mend my ways 🙂
0 Thanks
Reply
Highlighted
Advocate

Re: Hub Two and Network switches

@Mark_Weinreb 

 

1. Yes same cable used.

2. I used my cables.

 

@RoyBand Mark

I'll recheck all cables.

 

Thank you both for your ideas and suggestions.

0 Thanks
Reply
Highlighted
Legend 5
Legend 5

Re: Hub Two and Network switches

Hi @Sunrise 

 

Are you referring to an Ethernet Hub switch with a number of outgoing Ethernet ports ?

 

If not then ignore the rest of my post.

 

 Should you be using an Ethernet Hub switch is it a managed or unmanaged switch ?

 

I use a Trendnet unmanaged 8 port Ethernet Hub switch on my NowTV Hub 2 and it was plug & play and works seamlessly for me on my NowTV Hub 2 Router.

 

If you are using an unmanaged switch have you tried pressing the reset button on the back of the Router for about 10 to 15 seconds ?

 

Should it be a managed switch then there would be some configuration involved on the Router (not sure what mind because my networking knowledge is limited).

 

Perhaps post the make and model of your Ethernet Hub switch on here ?

0 Thanks
Reply